The new O2 System and Radio Mic install

Over the summer, when it was still too warm to work on the trailer top, I managed to finish the plumbing for the oxygen system.

I purchased a Mountain High System last spring and after careful studying on other gliders O2 systems, I planned out one that I believe will work just fine in the Libelle.

I found that the first stage needed to face down with my planned arrangement.

I mounted the refill port and tank gauge where it was accessible though the hat-self cover.

I originally bought the standard 3' high pressure hose, but I found that it was too short for where I needed to read the gauge in the cockpit. So I had to reorder a 5' hose. There were already small holes drilled in the ribs, I reused them to strap the hose in place, and ran it thought the glass straps in the side and under the seat pan tray lip.

Don't worry about that dangling chain on the refill port cover. I will get a better one that will secure the cap.

I drilled a opening in the lip and mounted the cockpit gauge. I also cut a notch in the seat pan lip to slide under the gauge.

While I was working on that side, I attached the boom microphone mount and ran the cable down the side. The cockpit padding will cover the cable when the plane is finished.

The next step was how to run the low pressure hose and still keep it away from anything that will hang up the controls or pinch the hose.

I ran the hose along the rear wing pin suspension tube and carefully strapped it down with plastic ties. There were holes in the ribs were I ran the tube in, through and around to avoid the aileron yoke and elevator rod.

The hose the was run through the glass straps into and under the right side seat pan tray lip.

Mountain High had a panel mount hose port that fit perfectly in the tray lip. I cut an opening in the seat pan for the port access. I will use the plastic hose to attach the demand regulator, and fit it into the side padding pocket.

It's now the end of September, the temperature is falling. It's time to finish the damn trailer!

UPDATE

Here is a revision to the low pressure hose install. A blog reader, Mark , suggested an excellent idea to prevent the hose from getting pinched by the plastic tires. He suggested that I shield the hose with a ridged plastic tube. I found that the tube I'm using for the steel wire shield had in ID the was just a shade wider than the OD of the low pressure hose. It was a perfect fit. And was rigid enough to prevent the plastic ties from biting into the low pressure line.


Again, Thank you Mark!

The Dog Days of Summer

Well, I have not been doing much work on this project since the first weeks of June. Summer came in Hot and heavy. It has been too warm to work with the fiberglass resin, so finishing the front of the trailer has been put on hold until it cools down.

I have been busy with school, and since I have finished this semester, I will finish wiring the fuselage and plumb the O2 system.

I have even taken some time off to do something unusual ... like ... fly!

More to come in the next couple of weeks!

The Trailer! Part 5a - UPDATE!

I know there is more to this post trail, but I had to at least show you all what I did last weekend. 

I managed to slide the back half onto the trailer frame, by myself.

I had to make some slight augmentations to the rear hoops and to the fiberglass tube supports, to get the top to sit correctly. One of the hoops will need to be rewelded after I get the top together.

I still need to do some cleanup on the frame top and the shell, so the back fits square. Once this is done. I will attempt to screw the shell to the top frame.

The Trailer! Part 5 - Making molds, breaking rules, and losing my mind!!

Back to report the latest progress on the trailer.

The trailer is back from being in storage at the Sandia Trailer. I was finally able to afford to pay the balance and bring it home to work on "Phase IV"

They did a great job installing the side skins and new floor.

And the jinx is still with the trailer.... when I was pulling the trailer out of storage yard, the turn was tight, and my tailgate was down at the time, holding the wood that was used as a cover, so, the gate tore into the skin on the front of the trailer!... Shit!

Before I can build the first mold, I needed to make room in the garage. Since I had no place to store the wings, I had to cocoon them in plastic, and store them outside. (I hated to do it, but it was my only only option.

I purchase the wood for the mold frame last year, while I still had money. The design of the molds will allow me to dis-assemble them from around the fiberglass cast. The first part of the mold was the top of the trailer. This also became the base.

Using the plans that I drew up, I created the side frames using 2x4's and cover the inside of the mold with wall paneling.

The next step was tricky. Since the top was made with two sheets of finished plywood, which where 4'x8' in size, the width of the top was two inches too narrow. the base width of the trailer sides needed to be just over 4' 1" to mate with the lower frame on the trailer top. I added scraps of wood to bring the base mount out to accommodate the attachment of the side panels.

Once the sides were up, the main box mold was finished, now I needed to devise a way to close off the open slit that runs the full length of the mold were the sides align with the base top, then the end cap.

I found that the cheap wall paneling was easy to cut, and I came up with a way to create a bevel top edge.





I secured the panel material with a hot glue gun and aluminum duct tape.

The end cap was simple to make. I just used a strip of the paneling and then taped it up.

With the mold finished, I'm ready to seal the wood and paneling matrial with a fiberglass mold release agent.

This mold is 16' long. and is almost 2/3rds of the length of the trailer.

To prevent the fiberglass resin sticking to the material I used release wax and a solution of PVA. After the PVA dried, I dropped in a layer of peel ply nylon.

The nylon was attached using masking tape and staples.

The first layer applied was the 10oz cloth.

Followed by the 6oz fiberlass mat. Mat is the biggest pain in the ass to use. The only plus side it, it adds bulk quickly, and adds greater strength. The down side is, fibers get everywhere, and it soaks up a lot of resin!... Gallons of it!





This concludes the first stage of the fiberglass top. This will cover the back 2/3rds of the trailer.

The last layer was an 18oz fiberglass roving. After the resin cured fully, I started to lay in the internal support structure. The material that was recommened for this purpose, was cardboard tubing. The tubes were cut in half, and the taped in place.









After the tubes were taped in, I was ready to fiberglass them in place. I used two layers of  fiber glass tape.






The resin soaked into the cardboard, making it extra ridged.

After the tube supports were glassed in, I was ready to pop the mold off. The sides for the most part seperated with little effort. There was only a couple of areas that the resin adhered to the paneling material.


I used wooded shims to pop the glass cast from the bottom plywood base.

The verical fin cover was made from a male mold, made of foam.

I covered the mold with aluminum tape and then waxed the mold with release wax.

The same number of layers of fiberglass was applied to the mold as match the trailer top.

The trailer shell was rotated right-side-up and stabilized with saw horses.

The fincap was then mounted to the top and fiberglassed in place.  Both, on the outside, and then inside.

The skin was fairly smooth, but are areas that needed attention.

Primer was used to find the areas that needed to be filled.

The fin cap required more work, since it was popped off a male mold. The resin voids and pits holes needed to be filled and sanded.






While this work was going on, and moving the top around, I had to add addition glass strips to the tube supports, since I noticed some areas that were stressed.

I relalized that I would need some additional steel loops in the trailer top to support the area were the two parts would be mated together, and also the front area for the access hatch.




Making the forward section will be a challange, now that the temperature is in the 80's here. I will be casting in the early hours before sunrise, or in the late evening, when it starts to cool down.

Before I can make that front portion, I will need to make room in the garage, and that means mounting the back half to the trailer.

Humpty Dumpty - Part 2, time to get those parts back in!

Now that the main pneumatic tubing has been installed, and the wiring trunk for the batteries and the speaker was pulled, it's time to get hardware re-installed.

It was a joy installing the rudder yoke.

I found that the new battery box was just wide enough to prevent the top bracket support from aligning with the holes in the wheel well sides. I had to grind away a notch on both sides to allow the top bracket to mate up with the holes. The box was mounted on the same ledge as the original, but I did not notice that the brackets, when installed went up on both sides of the battery box.  

Fortunately, the bottom of the box was extra thick, and I didn't have to cut into opening.

After the brackets were mounted, I installed the yoke. There was no vertical play in the bearing, and no room for shims or washers, with the exception for the washer needed for the nut.

I attached the push rod for the rudder to the yoke, and found that it was binding through the full range of motion. While the yoke and mounts aligning to there original positions, the rudder push rod seems to require a slight uplift to attach it to the yoke arm. This will require an inspection from Robert before the flight tests.

During the motion range testing, I noticed that the nylon wheels that the push rod travels on were not moving, and that the rod was just sliding over them. Using a long tube, I was able to get them freed up by applying a fine silicon fluid in the bearings of the nylon wheels. After the wheels were able to rotate, the push rod moves better now. Is there a better lubrication for them? They sit about four feet into the fuselage, and out of reach to get at them without using a long straw!

I was ready to install the main gear struts and arm. I painted the gear well white to seal the fiberglass from oil grease and dirt.

When it came time to but the struts in, I found that the forward shims were too tight due to the coat of paint near the openings. This required some cleanup before the struts would fit in place.

I had to install the main wheel back on the struts.

It has been two years since these parts were together.

Back inside, there were two parts that needed to be installed to help prevent the strut rods from falling out. The rear strut rod is secured by two bolts mounted through the strut and rod in the wheel well. Also the actuator arm was bolted in.

The forward strut rod is secured by a heavy washer and cotter pin attachment through a hole drilled through the end of the rod... Funny, I never removed this from my bird when I was taking the gear apart!?!?!?

How long were these parts missing?

I was able to see what parts were missing after inspecting a Libelle at Roberts shop!

I found the parts needed at the hardware shop, and they were approved to be used.

It would have been a bad day for someone landing this glider if that rod slipped in the gear shaft by just an inch or two.

As part of an AD note, there were two rudder yoke stops that needed to be mounted to the outside of the gear well wall.

These parts were installed per TN 201-15

The gear and aileron actuators were installed. These parts needed to be jockeyed around when the push rods were installed.  

The bolts are a tight fit when it comes time to inserting them into the bearings.


I'm sure the stream of obscenities are still hovering over the skies of Edgewood after my ordeal with installing them!

During the install, I found that the Capacity flask was too close to the actuation of the main gear push rod. I had to pop off the holds and move them a little further aft of their original mounting location.

The aileron actuator lever was also a tight fit.

The stick, airbrake handle-rod and landing gear handle-rod were ready to be installed next.

For the most part, the stick installation was straight forward, although, some of the bolts needed to be inserted into the bearings and rods before the stick and the housing were reseated on the tray. I wrapped plastic around the handle to prevent damaging it.

The plastic tubing used to shield the steel cables for the rudder pedal adjustment, and the tow release, needed to be pre-fitted before the final installation.

The final push rods were installed to complete this stage.

Last but not least, the airbrake and landing gear handles and rods were installed.

I wrapped plastic on the handles to protect them.

The steel cables were pulled though the center column support for the rudder pedal adjustment and the tow release. I then feed the brake cable into the handle on the stick.

The landing gear rod was installed to the linkage, and tested. The over-center adjustments will be checked by Robert before the glider can be signed off. 

The final attachements are the aileron linkages,

and the airbrake actuator.



The air brake actuator rod will be installed after painting, I don't want to damage the paint on this part before we start flying the glider.

All of these parts will need to be adjusted at the shop when we can finally test fit the wings and control surfaces.

With the majority of the inner connection completed, the Insturment panel finished, the next post on this sub-topic will cover the electrical wiring connections, speaker, PPT button and the microphone.

But this will need to wait a bit longer... The weather here has given me a break to start on building the new fiberglass trailer top!

Yet, another nightmare is just begining!